Print Catalogs

Legacy® Shop Notes

Video Clips

News

Links

Order Information

Custom Tools

Sharpening
Home > Magnate Router Bits & Accessories > O-Flute
We found 149 results matching your criteria.
O-Flute 1 Flute Up-Cut Spiral Router Bit Solid Carbide For Rigid Plastic, Acrylics & Nylons O-Flute 1 Flute Down-Cut Spiral Router Bit Solid Carbide For Rigid Plastic, Acrylics & Nylons O-Flute 1 Flute Polished Up-Cut Spiral Router Bit Solid Carbide, For Hard Plastics and Solid Surface

Solid Carbide For Rigid Plastic, Acrylics & Nylons more info

Solid Carbide For Rigid Plastic, Acrylics & Nylons more info

Solid Carbide, For Hard Plastics and Solid Surface more info
O-Flute 1 Flute Polished Down-Cut Spiral Router Bit Solid Carbide, For Hard Plastics and Solid Surface O-Flute 1 Flute Polished Up-Cut Spiral Router Bit Solid Carbide, For Soft Plastics, Aluminum and Solid Surface O-Flute 1 Flute Polished Down-Cut Spiral Router Bit Solid Carbide, For Soft Plastics, Aluminum and Solid Surface

Solid Carbide, For Hard Plastics and Solid Surface more info

Solid Carbide, For Soft Plastics, Aluminum and Solid Surface more info

Solid Carbide, For Soft Plastics, Aluminum and Solid Surface more info
O-Flute 2 Flute Up-Cut Spiral Router Bit Solid Carbide, For Harder Plastics and Aluminum O-Flute 2 Flute Down-Cut Spiral Router Bit Solid Carbide, For Harder Plastics and Aluminum O-Flute 2-Flute Slow Up-Cut Spiral Router Bit Solid Carbide; For Plastics and Solid Surface

Solid Carbide, For Harder Plastics and Aluminum more info

Solid Carbide, For Harder Plastics and Aluminum more info

Solid Carbide; For Plastics and Solid Surface more info
O-Flute 2-Flute Slow Down-Cut Spiral Router Bit Solid Carbide; For Plastics and Solid Surface O-Flute 1 Flute Straight Router bit Solid Carbide, For Soft Plastics O-Flute 1 Flute Straight Polished Router bit, Left-Hand Solid Carbide, For Hard and Soft Plastics

Solid Carbide; For Plastics and Solid Surface more info

Solid Carbide, For Soft Plastics more info

Solid Carbide, For Hard and Soft Plastics more info
O-Flute 2 Flute Straight Router bit Solid Carbide, For Medium Plastic O-Flute Spiral Up-Cut Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute 1/4" Cutting Diameter, Solid Carbide, Polished For Plastic and Solid Surface O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute 1/4" Cutting Diameter, Solid Carbide, For Plastic and Solid Surface Materials

Solid Carbide, For Medium Plastic more info

1/4" Cutting Diameter, Solid Carbide, Polished For Plastic and Solid Surface more info

1/4" Cutting Diameter, Solid Carbide, For Plastic and Solid Surface Materials more info
O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 2 Flute 1/4" Cutting Diameter, Solid Carbide, For Plastic Sheets or Parts O-Flute Straight Edge Rounding Router Bit, 3/8" Shank Diameter 2 Flute 3/8" Cutting Diameter, Solid Carbide, For Plastic Sheets or Parts O-Flute Straight Edge Rounding Router Bit, 1/2" Shank Diameter 2 Flute, Solid Carbide, For Plastic Sheets or Parts

1/4" Cutting Diameter, Solid Carbide, For Plastic Sheets or Parts more info

3/8" Cutting Diameter, Solid Carbide, For Plastic Sheets or Parts more info

2 Flute, Solid Carbide, For Plastic Sheets or Parts more info
Sort By:
Page of 2
Magnate 2632 O-Flute 2 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2632 O-Flute 2 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $18.79
Our Price: $15.03
Savings: $3.76
Qty Add
Magnate 2890 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2890 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $21.75
Our Price: $17.40
Savings: $4.35
Qty Add
Magnate 1922 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1922 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $28.46
Our Price: $22.77
Savings: $5.69
Qty Add
Magnate 2899 O-Flute 1 Flute Down-Cut Spiral Router Bit - 5/16" Cutting Diameter; 7/8" Cutting Length; 5/16" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2899 O-Flute 1 Flute Down-Cut Spiral Router Bit - 5/16" Cutting Diameter; 7/8" Cutting Length; 5/16" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $28.92
Our Price: $23.13
Savings: $5.79
Qty Add
Magnate 2622 O-Flute 2 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2622 O-Flute 2 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $31.04
Our Price: $24.83
Savings: $6.21
Qty Add
Magnate 1925 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1925 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $33.17
Our Price: $26.53
Savings: $6.64
Qty Add
Magnate 1926 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1926 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $33.17
Our Price: $26.53
Savings: $6.64
Qty Add
Magnate 2941 O-Flute 2 Flute Straight Router bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2941 O-Flute 2 Flute Straight Router bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $34.17
Our Price: $27.33
Savings: $6.84
Qty Add
Magnate 2963 O-Flute 2 Flute Straight Router bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2963 O-Flute 2 Flute Straight Router bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $34.17
Our Price: $27.33
Savings: $6.84
Qty Add
Magnate 2964 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2964 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $34.17
Our Price: $27.33
Savings: $6.84
Qty Add
Magnate 2621 O-Flute 2 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2621 O-Flute 2 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $34.85
Our Price: $27.88
Savings: $6.97
Qty Add
Magnate 2945 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2945 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.56
Our Price: $28.45
Savings: $7.11
Qty Add
Magnate 1923 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1923 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 1927 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1927 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2881 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2881 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2882 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2882 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2561 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2561 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2581 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2581 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2891 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2891 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2892 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2892 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.94
Our Price: $28.75
Savings: $7.19
Qty Add
Magnate 2880 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2880 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $35.96
Our Price: $28.77
Savings: $7.19
Qty Add
Magnate 2623 O-Flute 2 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2623 O-Flute 2 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $36.88
Our Price: $29.50
Savings: $7.38
Qty Add
Magnate 2633 O-Flute 2 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2633 O-Flute 2 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $36.88
Our Price: $29.50
Savings: $7.38
Qty Add
Magnate 1901 O-Flute 1 Flute Straight Router bit - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1901 O-Flute 1 Flute Straight Router bit - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $37.13
Our Price: $29.70
Savings: $7.43
Qty Add
Magnate 1902 O-Flute 1 Flute Straight Router bit - 5/32" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1902 O-Flute 1 Flute Straight Router bit - 5/32" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $37.13
Our Price: $29.70
Savings: $7.43
Qty Add
Magnate 1903 O-Flute 1 Flute Straight Router bit - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1903 O-Flute 1 Flute Straight Router bit - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $37.13
Our Price: $29.70
Savings: $7.43
Qty Add
Magnate 1905 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1905 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $37.13
Our Price: $29.70
Savings: $7.43
Qty Add
Magnate 2897 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2897 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $37.62
Our Price: $30.10
Savings: $7.52
Qty Add
Magnate 2887 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2887 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $38.33
Our Price: $30.67
Savings: $7.66
Qty Add
Magnate 1909 O-Flute 1 Flute Straight Router bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1909 O-Flute 1 Flute Straight Router bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $39.06
Our Price: $31.25
Savings: $7.81
Qty Add
Magnate 1910 O-Flute 1 Flute Straight Router bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1910 O-Flute 1 Flute Straight Router bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $39.06
Our Price: $31.25
Savings: $7.81
Qty Add
Magnate 1912 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1912 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $39.42
Our Price: $31.53
Savings: $7.89
Qty Add
Magnate 2943 O-Flute 2 Flute Straight Router bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2943 O-Flute 2 Flute Straight Router bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $39.96
Our Price: $31.97
Savings: $7.99
Qty Add
Magnate 1906 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1906 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $40.46
Our Price: $32.37
Savings: $8.09
Qty Add
Magnate 1904 O-Flute 1 Flute Straight Router bit - 7/32" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1904 O-Flute 1 Flute Straight Router bit - 7/32" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $40.96
Our Price: $32.77
Savings: $8.19
Qty Add
Magnate 1911 O-Flute 1 Flute Straight Router bit - 1/8" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1911 O-Flute 1 Flute Straight Router bit - 1/8" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $41.96
Our Price: $33.57
Savings: $8.39
Qty Add
Magnate 2942 O-Flute 2 Flute Straight Router bit - 5/32" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2942 O-Flute 2 Flute Straight Router bit - 5/32" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $43.15
Our Price: $34.52
Savings: $8.63
Qty Add
Magnate 2045 O-Flute 2-Flute Slow Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 2-1/2" Overall Length; 1/4" Shank Diameter; Solid Carbide; For Plastics and Solid Surface
Magnate 2045 O-Flute 2-Flute Slow Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 2-1/2" Overall Length; 1/4" Shank Diameter; Solid Carbide; For Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $43.56
Our Price: $34.85
Savings: $8.71
Qty Add
Magnate 2145 O-Flute 2-Flute Slow Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 2-1/2" Overall Length; 1/4" Shank Diameter; Solid Carbide; For Plastics and Solid Surface
Magnate 2145 O-Flute 2-Flute Slow Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 2-1/2" Overall Length; 1/4" Shank Diameter; Solid Carbide; For Plastics and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $43.56
Our Price: $34.85
Savings: $8.71
Qty Add
Magnate 2648 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2648 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $43.56
Our Price: $34.85
Savings: $8.71
Qty Add
Magnate 2649 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2649 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $43.56
Our Price: $34.85
Savings: $8.71
Qty Add
Magnate 2562 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2562 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2564 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2564 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2565 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2565 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2568 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2568 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2569 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2569 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/8" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2560 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2560 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2640 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2640 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/4" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2641 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2641 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2642 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2642 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2644 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2644 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 2653 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2653 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $45.19
Our Price: $36.15
Savings: $9.04
Qty Add
Magnate 1921 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1921 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $27.44
Our Price: $37.13
Qty Add
Magnate 1915 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 3-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1915 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 3-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $46.79
Our Price: $37.43
Savings: $9.36
Qty Add
Magnate 2563 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2563 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $48.29
Our Price: $38.63
Savings: $9.66
Qty Add
Magnate 2643 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2643 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $48.29
Our Price: $38.63
Savings: $9.66
Qty Add
Magnate 1913 O-Flute 1 Flute Straight Router bit - 3/16" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1913 O-Flute 1 Flute Straight Router bit - 3/16" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $48.42
Our Price: $38.73
Savings: $9.69
Qty Add
Magnate 2624 O-Flute 2 Flute Up-Cut Spiral Router Bit - 5/16" Cutting Diameter; 1" Cutting Length; 5/16" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2624 O-Flute 2 Flute Up-Cut Spiral Router Bit - 5/16" Cutting Diameter; 1" Cutting Length; 5/16" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.23
Our Price: $39.38
Savings: $9.85
Qty Add
Magnate 2634 O-Flute 2 Flute Down-Cut Spiral Router Bit - 5/16" Cutting Diameter; 1" Cutting Length; 5/16" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2634 O-Flute 2 Flute Down-Cut Spiral Router Bit - 5/16" Cutting Diameter; 1" Cutting Length; 5/16" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.23
Our Price: $39.38
Savings: $9.85
Qty Add
Magnate 2583 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2583 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.33
Our Price: $39.47
Savings: $9.86
Qty Add
Magnate 2889 O-Flute 1 Flute Up-Cut Spiral Router Bit - 5/16" Cutting Diameter; 7/8" Cutting Length; 5/16" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2889 O-Flute 1 Flute Up-Cut Spiral Router Bit - 5/16" Cutting Diameter; 7/8" Cutting Length; 5/16" Shank Diameter; 2-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.50
Our Price: $39.60
Savings: $9.90
Qty Add
Magnate 2567 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2567 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.69
Our Price: $39.75
Savings: $9.94
Qty Add
Magnate 2585 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 7/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2585 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 7/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.73
Our Price: $39.78
Savings: $9.95
Qty Add
Magnate 2965 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2965 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $49.79
Our Price: $39.83
Savings: $9.96
Qty Add
Magnate 2594 1 Flute O-Flute Spiral Router Bit For Hard Plastics - Down Cut; 3/8" Cutting Diameter; 1-1/8" Cutting Length; 3/8" Shank Diameter; 3" Overall Length
Magnate 2594 1 Flute O-Flute Spiral Router Bit For Hard Plastics - Down Cut; 3/8" Cutting Diameter; 1-1/8" Cutting Length; 3/8" Shank Diameter; 3" Overall Length
more info
Our Price: $40.38
Qty Add
Magnate 2647 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2647 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $50.98
Our Price: $40.78
Savings: $10.20
Qty Add
Magnate 1924 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1924 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $51.33
Our Price: $41.07
Savings: $10.26
Qty Add
Magnate 2961 O-Flute 2 Flute Straight Router bit - 1/8" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2961 O-Flute 2 Flute Straight Router bit - 1/8" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $51.65
Our Price: $41.32
Savings: $10.33
Qty Add
Magnate 2888 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/2" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2888 O-Flute 1 Flute Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/2" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $52.27
Our Price: $41.82
Savings: $10.45
Qty Add
Magnate 2895 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1-5/8" Cutting Length; 3/8" Shank Diameter; 3-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2895 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1-5/8" Cutting Length; 3/8" Shank Diameter; 3-1/2" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $52.58
Our Price: $42.07
Savings: $10.51
Qty Add
Magnate 2893 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2893 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $52.96
Our Price: $42.37
Savings: $10.59
Qty Add
Magnate 2946 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 3-1/2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2946 O-Flute 2 Flute Straight Router bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 3-1/2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $53.25
Our Price: $42.60
Savings: $10.65
Qty Add
Magnate 2821 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Magnate 2821 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 1/8" Cutting Diameter; 3/8" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $53.29
Our Price: $42.63
Savings: $10.66
Qty Add
Magnate 2823 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Magnate 2823 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 3/16" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $53.29
Our Price: $42.63
Savings: $10.66
Qty Add
Magnate 2825 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Magnate 2825 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $53.29
Our Price: $42.63
Savings: $10.66
Qty Add
Magnate 1998 Polished Multi-Grind O-Flute, 1 Flute - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length
Magnate 1998 Polished Multi-Grind O-Flute, 1 Flute - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length
more info
Our Price: $43.00
Qty Add
Magnate 2661 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2661 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/8" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $53.77
Our Price: $43.02
Savings: $10.75
Qty Add
Magnate 2663 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2663 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 3/16" Cutting Diameter; 5/8" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $53.77
Our Price: $43.02
Savings: $10.75
Qty Add
Magnate 2665 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2665 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.23
Our Price: $43.38
Savings: $10.85
Qty Add
Magnate 2625 O-Flute 2 Flute Up-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2625 O-Flute 2 Flute Up-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.56
Our Price: $43.65
Savings: $10.91
Qty Add
Magnate 2635 O-Flute 2 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
Magnate 2635 O-Flute 2 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide, For Harder Plastics and Aluminum
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.56
Our Price: $43.65
Savings: $10.91
Qty Add
Magnate 2883 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2883 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.98
Our Price: $43.98
Savings: $11.00
Qty Add
Magnate 2884 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1-1/8" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2884 O-Flute 1 Flute Up-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1-1/8" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.98
Our Price: $43.98
Savings: $11.00
Qty Add
Magnate 2894 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1-1/8" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2894 O-Flute 1 Flute Down-Cut Spiral Router Bit - 3/8" Cutting Diameter; 1-1/8" Cutting Length; 3/8" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.98
Our Price: $43.98
Savings: $11.00
Qty Add
Magnate 2651 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 5/16" Cutting Diameter; 1" Cutting Length; 5/16" Shank Diameter; 3" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2651 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 5/16" Cutting Diameter; 1" Cutting Length; 5/16" Shank Diameter; 3" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $54.98
Our Price: $43.98
Savings: $11.00
Qty Add
Magnate 1928 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 1928 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $55.08
Our Price: $44.07
Savings: $11.01
Qty Add
Magnate 2587 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2587 O-Flute 1 Flute Polished Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $55.08
Our Price: $44.07
Savings: $11.01
Qty Add
Magnate 2826 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 5/32" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Magnate 2826 O-Flute 1 Flute Straight Polished Router bit, Left-Hand - 5/32" Cutting Diameter; 1/2" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard and Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $55.25
Our Price: $44.20
Savings: $11.05
Qty Add
Magnate 1916 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1916 O-Flute 1 Flute Straight Router bit - 1/4" Cutting Diameter; 1-1/4" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $56.00
Our Price: $44.80
Savings: $11.20
Qty Add
Magnate 2944 O-Flute 2 Flute Straight Router bit - 3/16" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2944 O-Flute 2 Flute Straight Router bit - 3/16" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 4" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $56.48
Our Price: $45.18
Savings: $11.30
Qty Add
Magnate 1918 O-Flute 1 Flute Straight Router bit - 3/8" Cutting Diameter; 7/8" Cutting Length; 3/8" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Magnate 1918 O-Flute 1 Flute Straight Router bit - 3/8" Cutting Diameter; 7/8" Cutting Length; 3/8" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $56.73
Our Price: $45.38
Savings: $11.35
Qty Add
Magnate 2898 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/2" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
Magnate 2898 O-Flute 1 Flute Down-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1-1/2" Cutting Length; 1/4" Shank Diameter; 3" Overall Length; Solid Carbide For Rigid Plastic, Acrylics, Nylons, Solid Surface, Aluminum and Type I Foams
A down-cut spiral bit is used where a downward chip removal and a good finish on top are required. A down-cut spiral bit provides downward pressure on the material and leaves an excellent finish on the top.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $57.90
Our Price: $46.32
Savings: $11.58
Qty Add
Magnate 1981 O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute - 5/32" Opening; 3/8" Cutting Length; .195" Small Diameter; 1/8" Radius; 2-1/2" Overall Length
Magnate 1981 O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute - 5/32" Opening; 3/8" Cutting Length; .195" Small Diameter; 1/8" Radius; 2-1/2" Overall Length
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $58.08
Our Price: $46.47
Savings: $11.61
Qty Add
Magnate 1982 O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute - 7/32" Opening; 3/8" Cutting Length; .180" Small Diameter; 3/16" Radius; 2-1/2" Overall Length
Magnate 1982 O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute - 7/32" Opening; 3/8" Cutting Length; .180" Small Diameter; 3/16" Radius; 2-1/2" Overall Length
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $58.08
Our Price: $46.47
Savings: $11.61
Qty Add
Magnate 1983 O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute - 9/32" Opening; 3/8" Cutting Length; .163" Small Diameter; 1/4" Radius; 2-1/2" Overall Length
Magnate 1983 O-Flute Straight Edge Rounding Router Bit, 1/4" Shank Diameter 1 Flute - 9/32" Opening; 3/8" Cutting Length; .163" Small Diameter; 1/4" Radius; 2-1/2" Overall Length
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $58.08
Our Price: $46.47
Savings: $11.61
Qty Add
Magnate 2947 O-Flute 2 Flute Straight Router bit - 3/8" Cutting Diameter; 7/8" Cutting Length; 3/8" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Magnate 2947 O-Flute 2 Flute Straight Router bit - 3/8" Cutting Diameter; 7/8" Cutting Length; 3/8" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Medium Plastic
Always consult your router's operation manual before setting the RPM for your router bit.    If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions.    1) Up to 24,000 RPM for bits with an overall diameter of 1".   2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2".   3) Up to 18,000 RPM for bits with an overall diameter of 2".   4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2".   5) Up to 12,000 RPM for bits with an overall diameter of 3".   6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $58.65
Our Price: $46.92
Savings: $11.73
Qty Add
Magnate 2570 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2570 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/8" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $59.29
Our Price: $47.43
Savings: $11.86
Qty Add
Magnate 2571 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 7/32" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
Magnate 2571 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 7/32" Cutting Diameter; 3/4" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Hard Plastics and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $59.29
Our Price: $47.43
Savings: $11.86
Qty Add
Magnate 2645 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2645 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/4" Cutting Diameter; 1" Cutting Length; 1/4" Shank Diameter; 2-1/2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $59.29
Our Price: $47.43
Savings: $11.86
Qty Add
Magnate 2646 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/16" Cutting Diameter; 1/4" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
Magnate 2646 O-Flute 1 Flute Polished Up-Cut Spiral Router Bit - 1/16" Cutting Diameter; 1/4" Cutting Length; 1/4" Shank Diameter; 2" Overall Length; Solid Carbide, For Soft Plastics, Aluminum and Solid Surface
A up-cut spiral bit is used where an upward chip removal and a good finish on bottom are required. When using an up-cut spiral bit, chip removal is optimized but adequate hold down is also needed.

Always consult your router's operation manual before setting the RPM for your router bit. If a router bit does not include a recommended speed chart, you may begin at approximately 2,000 RPM below the maximum speed listed in the guide below. Please note that these speeds are for reference only the optimal speed may vary depending on factors such as bit size, material type, and cutting conditions. 1) Up to 24,000 RPM for bits with an overall diameter of 1". 2) Up to 20,000 RPM for bits with an overall diameter of 1-1/2". 3) Up to 18,000 RPM for bits with an overall diameter of 2". 4) Up to 16,000 RPM for bits with an overall diameter of 2-1/2". 5) Up to 12,000 RPM for bits with an overall diameter of 3". 6) Up to 10,000 RPM for bits with an overall diameter of 3-1/2". more info
List Price: $59.29
Our Price: $47.43
Savings: $11.86
Qty Add
To add the above items to your cart, click the "Add" checkboxes then click "Add To Cart" >>>